An anonymous reader shared this report from the Washington Post: Nearly any material can be used to turn the energy in air humidity into electricity, scientists found in a discovery that could lead to continuously producing clean energy with little pollution. The research, published in a paper in Advanced Materials, builds on 2020 work that first showed energy could be pulled from the moisture in the air using material harvested from bacteria. The new study shows nearly any material can be used, like wood or silicon, as long as it can be smashed into small particles and remade with microscopic pores...

The air-powered generator, known as an "Air-gen," would offer continuous clean electricity since it uses the energy from humidity, which is always present, rather than depending on the sun or wind... The device, the size of a fingernail and thinner than a single hair, is dotted with tiny holes known as nanopores. The holes have a diameter smaller than 100 nanometers, or less than a thousandth of the width of a strand of human hair. The tiny holes allow the water in the air to pass through in a way that would create a charge imbalance in the upper and lower parts of the device, effectively creating a battery that runs continuously. "We are opening up a wide door for harvesting clean electricity from thin air," Xiaomeng Liu, another author and a UMass engineering graduate student, said in a statement.

While one prototype only produces a small amount of energy — almost enough to power a dot of light on a big screen — because of its size, Yao said Air-gens can be stacked on top of each other, potentially with spaces of air in between. Storing the electricity is a separate issue, he added. Yao estimated that roughly 1 billion Air-gens, stacked to be roughly the size of a refrigerator, could produce a kilowatt and partly power a home in ideal conditions. The team hopes to lower both the number of devices needed and the space they take up by making the tool more efficient...

It could be embedded in wall paint in a home, made at a larger scale in unused space in a city or littered throughout an office's hard-to-get-to spaces. And because it can use nearly any material, it could extract less from the environment than other renewable forms of energy. "The entire earth is covered with a thick layer of humidity," Yao said. "It's an enormous source of clean energy. This is just the beginning in making use of that."
More information from the Boston Globe.

Thanks to long-time Slashdot reader SpzToid for sharing the article.

An anonymous reader quotes a report from Ars Technica: HP printers have received a lot of flak historically and recently for invasive firmware updates that end up preventing customers from using ink with their printers. HP also encourages printer customers to sign up for HP+, a program that includes a free ink-subscription trial and irremovable firmware that allows HP to brick the ink when it sees fit. Despite this, HP markets dozens of its printers with Dynamic Security and the optional HP+ feature as being in the Electronic Product Environmental Assessment Tool (EPEAT) registry, suggesting that these printers are built with the environment in mind and, more specifically, do not block third-party ink cartridges. Considering Dynamic Security and HP+ printers do exactly that, the International Imaging Technology Council (IITC) wants the General Electronics Council (GEC), which is in charge of the EPEAT registry, to revoke at least 101 HP printer models from the EPEAT registry, which HP has "made a mockery of."

For a printer to make the EPEAT registry, it's supposed to comply with the EPEAT Imaging Equipment Category Criteria, which is based on the 1680.2-2012 IEEE Standard for Environmental Assessment of Imaging Equipment (PDF). The IITC is hung up on section 4.9.2.1, which requires that registered products do not "prevent the use of nonmanufacturer cartridges and non-manufacturer containers" and that vendors provide documentation showing that the device isn't "designed to prevent the use of a non-manufacturer cartridge or non-manufacturer container." Well, as the IITC and consumers who found their inked bricked mid-print will tell you, that sounds an awful lot like what HP does with its Dynamic Security printers.

Diving deeper, the IITC's complaint claims that "in the last 8 weeks alone, HP has released 4 killer firmware updates targeting dozens of EPEAT-registered inkjet printers." "At least one of these recent updates specifically targeted a single producer of remanufactured cartridges while not having any impact on non-remanufactured third-party cartridges using functionally identical non-HP chips," the complaint reads. The trade group also claimed at least 26 "killer firmware updates" occurred on EPEAT-registered HP laser printers since October 2020. The complaint argues that the error message that users see -- "The indicated cartridges have been blocked by the printer firmware because they contain non-HP chips. This printer is intended to work only with new or reused cartridges that have a new or reused HP chip. Replace the indicated cartridges to continue printing" -- go against EPEAT requirements, yet HP markets dozens of Dynamic Security printers with EPEAT ecolabels. "The nonprofit trade association was founded in 2000 and says it represents 'toner and inkjet cartridge remanufacturers, component suppliers, and cartridge collectors in North America,'" notes Ars. "So its members stand to lose a lot of money from tactics like Dynamic Security. The IITC already filed a complaint to the GEC about HP in 2019 for firmware blocking non-HP ink, but there didn't seem to be any noticeable results."

"The group is biased regarding this topic, but its complaint still mirrors many problems and concerns that consumers and class-action lawsuits have detailed regarding HP printers' exclusive stance on ink. You can find the full complaint here."

Hyundai Motor and LG Energy have announced they will build a $4.3 billion electric battery plant as part of Hyundai's new electric vehicle assembly plant in southeast Georgia. From a report: The companies will split the investment, starting production as soon as late 2025. Hyundai Motor CEO Jaehoon Chang said in a statement that the battery plant would "create a strong foundation to lead the global EV transition," explaining the company wants to speed up efforts to produce electrified Hyundai and Kia vehicles in North America. "Hyundai Motor Group is focusing on its electrification efforts to secure a leadership position in the global auto industry," Chang said. The South Korean automaker said in 2022 it would invest $5.5 billion to assemble electric vehicles and batteries in Ellabell, just west of Savannah. The site is supposed to have 8,100 employees and is slated to begin producing vehicles in 2025.

An anonymous reader shares a report: Amazon's No. 1 bestselling printer is the HP Deskjet 2755e. It's not hard to see why. For just $85, you get a wireless color printer, scanner, and six months of free ink. It also comes with HP Plus, one of the most dastardly schemes Big Inkjet has ever unleashed. I'm not talking about how printers quietly waste their own ink, or pretend cartridges are empty when they're not, or lock out official cartridges from other regions. Heck, I'm not even talking about "Dynamic Security," the delightful feature where new HP firmware updates secretly contain malware that blocks batches of third-party cartridges while pretending to harden your printhead against hacks. No, the genius of HP's latest scheme is that it's hiding in plain sight, daring you to unwittingly sign away your rights. Take the free ink, and HP controls your printer for life.

First introduced in 2020 at the height of the pandemic, HP Plus was built around FOMO right from the start. You get just seven days to claim your free ink, starting the moment you plug a new printer into the wall. Act now, and it'll also extend your warranty a full year, give you an "Advanced HP Smart app," and plant trees on your behalf. Because why wouldn't you want to save the forest? Here's one reason, as detailed in a new complaint by the International Imaging Technology Council (IITC) that might turn into a false advertising fight: HP Plus comes with a firmware update that utterly removes your printer's ability to accept third-party ink. You have to buy "genuine" HP ink as long as you use the printer.

According to the International Energy Agency (IEA), investment in clean energy is set to surpass spending on fossil fuels in 2023, with solar projects expected to outpace oil production for the first time. Reuters reports: Annual investment in renewable energy is up by nearly a quarter since 2021 compared to a 15% rise for fossil fuels, the Paris-based energy watchdog said in its World Energy Investment report. Around 90% of that clean energy spending comes from advanced economies and China, however, highlighting the global divide between rich and poor countries as fossil fuel investment is still double the levels needed to reach net-zero emissions by mid-century.

Around $2.8 trillion is set to be invested in energy worldwide in 2023, of which more than $1.7 trillion is expected to go to renewables, nuclear power, electric vehicles, and efficiency improvements. The rest, or around $1 trillion, will go to oil, gas and coal, demand for the last of which will reach an all-time high or six times the level needed in 2030 to reach net zero by 2050.

Current fossil fuel spending is significantly higher than what it should be to reach the goal of net zero by mid-century, the agency said. In 2023, solar power spending is due to hit more than $1 billion a day or $382 billion for the year, while investment in oil production will stand at $371 billion. Investment in new fossil fuel supply will rise by 6% in 2023 to $950 billion, the IEA added.

The Tesla Model Y has become the world's best-selling car in the first quarter of 2023, according to industry analyst JATO Dynamics, making it the first time an electric vehicle (EV) has achieved this milestone. Electrek reports: The Model Y has dethroned the Toyota Corolla as the world's best-selling car in Q1 and looks like it may well maintain this position for the full year. JATO Dynamics analyst Felipe Munoz compiled the data for Motor1, showing that the Model Y had 267,200 sales in Q1, according to data from 53 markets and projections/estimates for the rest of the world. This put it ahead of the Corolla at 256,400 sales for the same period and significantly ahead of the other top-five cars, the Hilux, RAV4, and Camry, all from Toyota.

While we don't know if this placing will continue for the rest of the year, Model Y sales have been continually growing, whereas Corolla sales are trending slightly downward. One model is new and based on new technology, and the other is an old standard -- though the current iteration of both models came out in a similar time frame, 2018 for the Corolla and 2019 for Model Y. And given Tesla's massive price cuts this year on Model Y, this will surely make the car accessible to more people compared to 2022.

Indeed, Model Y sales are already growing compared to last year. In 2022, Tesla had two of the top ten cars in the world, with Model Y achieving 759k sales. That gives it an average quarterly run rate of 189k, and this year's Q1 number is a significant increase from that. If Model Y continues at this rate or sales continue to grow at all for the rest of this year, it will exit 2023 with over 1 million sales. The only other vehicle in the world to sell 1 million units last year was the Toyota Corolla, at 1.12 million. So it might be close at year's end, but we think it's likely that Model Y will maintain its position. "The achievement is even more impressive given Model Y's pricing and availability," adds Electrek. "While the Model Y does have broad availability in the world's largest markets, the Corolla is available everywhere. And despite recent price cuts, the Model Y at ~$40k (after credits) is still significantly more expensive than a base-model Corolla at $21k."

In other EV news, Ford and Tesla announced a partnership that will allow Ford owners access to more than 12,000 Tesla Superchargers across the U.S. and Canada starting early next year. "And, Ford's next-generation of EVs -- expected by mid-decade -- will include Tesla's charging plug, allowing owners of Ford vehicles to charge at Tesla Superchargers without an adapter, making Ford among the first automakers to explicitly tie into the network," reports CNBC.

An anonymous reader shares a report: I'm disappointed. I've been waiting for AMD and Nvidia to offer up more affordable options for this generation of GPUs that could really push 1440p into the mainstream, but what I've been reviewing over the past week hasn't lived up to my expectations. Nvidia and AMD are both releasing new GPUs this week that are aimed at the budget PC gaming market. After seven years of 1080p dominating the mainstream, I was hopeful this generation would deliver 1440p value cards. Instead, Nvidia has started shipping a $399 RTX 4060 Ti today that the company is positioning as a 1080p card and not the 1440p sweet spot it really should be at this price point.

AMD is aggressively pricing its new Radeon RX 7600 at just $269, and it's definitely more suited to the 1080p resolution at that price point and performance. I just wish there were an option between the $300 to $400 marks that offered enough performance to push us firmly into the 1440p era. More than 60 percent of PC gamers are playing at 1080p, according to Valve's latest Steam data. That means GPU makers like AMD and Nvidia don't have to target 1440p with cards that sell in high volume because demand seems to be low. Part of that low demand could be because a monitor upgrade isn't a common purchase for PC gamers, or they'd have to pay more for a graphics card to even support 1440p. That's probably why both of these cards also still ship with just 8GB of VRAM because why ship it with more if you're only targeting 1080p? A lower resolution doesn't need as much VRAM for texture quality. I've been testing both cards at 1080p and 1440p to get a good idea of where they sit in the GPU market right now. It's fair to say that the RTX 4060 Ti essentially offers the same 1440p performance as an RTX 3070 at 1440p for $399. That's $100 less than the RTX 3070's $499 price point, which, in October 2020, I said offered a 1440p sweet spot for games during that period of time. It's now nearly three years on, and I'd certainly expect more performance here at 1440p. Why is yesterday's 1440p card suddenly a 1080p one for Nvidia?

According to Ars Technica, some SanDisk Extreme SSDs are wiping people's data. While SanDisk told Ars that a firmware fix is coming "soon," owners with 2TB drives are out of luck. From the report: An Ars reader tipped us (thanks!) to online discussions filled with panicked and disappointed users detailing experiences with recently purchased Extreme V2 and Extreme Pro V2 portable SSDs. Most users seemed to be using a 4TB model, but there were also complaints from owners of 2TB drives.

Until now, there has been little public response from SanDisk, which has mostly referred online users to open a support ticket with SanDisk's technical support team. Questions about refunds have been left unanswered. When Ars contacted SanDisk about the issue, a company representative said: "Western Digital is aware of reports indicating some customers have experienced an issue with 4TB SanDisk Extreme and/or Extreme Pro portable SSDs (SDSSDE61-4T00 and SDSSDE81-4T00 respectively). We have resolved the issue and will publish a firmware update to our website soon. Customers with questions or who are experiencing issues should contact our Customer Support team for assistance."

SanDisk didn't answer our questions about refunds, whether or not the firmware would address issues with the 2TB models, what caused the issue, or when exactly this firmware fix will come. Some Reddit users have suggested that SanDisk has dragged its feet on the monthlong saga, with ian__ claiming they needed to collect "data to prove to SanDisk that it actually is more than a fluke." SanDisk's brief response to Ars' questions fails to clarify what's been going on behind the scenes.

"China delivered the latest salvo in an escalating semiconductor war with the U.S.," reports Bloomberg, "announcing that Micron Technology Inc. products have failed to pass a cybersecurity review in the country." In a statement Sunday, Beijing warned operators of key infrastructure against buying the company's goods, saying it found "relatively serious" cybersecurity risks in Micron products sold in the country. The components caused "significant security risks to our critical information infrastructure supply chain," which would affect national security, according to the statement from the Cyberspace Administration of China, or CAC...

Chinese officials privately say that the probe of Micron is part of a broader trend toward the dominance of "pro-retaliation" voices in Beijing, where national security concerns increasingly trump economic arguments. "No one should understand this decision by CAC as anything but retaliation for the US's export controls on semiconductors," said Holden Triplett, founder of Trenchcoat Advisors and a former FBI counterintelligence official in Beijing. "No foreign business operating in China should be deceived by this subterfuge. These are political actions pure and simple, and any business could be the next one to be made an example of." The move brings fresh uncertainty to the other US chipmakers that sell to China, the world's biggest market for semiconductors.
The article notes pointedly that memory chips "aren't usually considered a cybersecurity risk because they don't require any specific software or run code. They're mostly basic grids of transistors used for storing data and, as such, haven't typically been a vector of attack for hackers." The Associated Press describes China's move as "stepping up a feud with Washington over technology and security," adding that Chinese officials "appear to be struggling to find ways to retaliate without hurting China's smartphone producers and other industries and efforts to develop its own processor chip suppliers," which import more than $300 billion in foreign chips every year. An official review of Micron under China's increasingly stringent information security laws was announced April 4, hours after Japan joined Washington in imposing restrictions on Chinese access to technology to make processor chips on security grounds. Foreign companies have been rattled by police raids on two consulting firms, Bain & Co. and Capvision, and a due diligence firm, Mintz Group. Chinese authorities have declined to explain the raids but said foreign companies are obliged to obey the law.

There's shortages of young semiconductor engineers around the world, reports IEEE Spectrum — partially explained by this quote from Intel's director of university research collaboration. "We hear from academics that we're losing EE students to software. But we also need the software. I think it's a totality of 'We need more students in STEM careers.'"

So after America's CHIPS and Science Act "aimed at kick-starting chip manufacturing in the United States," the article notes that universities must attempt bring the U.S. "the qualified workforce needed to run these plants and design the chips." The United States today manufactures just 12 percent of the world's chips, down from 37 percent in 1990, according to a September 2020 report by the Semiconductor Industry Association. Over those decades, experts say, semiconductor and hardware education has stagnated. But for the CHIPS Act to succeed, each fab will need hundreds of skilled engineers and technicians of all stripes, with training ranging from two-year associate degrees to Ph.D.s. Engineering schools in the United States are now racing to produce that talent... There were around 20,000 job openings in the semiconductor industry at the end of 2022, according to Peter Bermel, an electrical and computer engineering professor at Purdue University. "Even if there's limited growth in this field, you'd need a minimum of 50,000 more hires in the next five years. We need to ramp up our efforts really quickly...."

More than being a partner, Intel sees itself as a catalyst for upgrading the higher-education system to produce the workforce it needs, says the company's director of university research collaboration, Gabriela Cruz Thompson. One of the few semiconductor companies still producing most of its wafers in the United States, Intel is expanding its fabs in Arizona, New Mexico, and Oregon. Of the 7,000 jobs created as a result, about 70 percent will be for people with two-year degrees... Since COVID, however, Intel has struggled to find enough operators and technicians with two-year degrees to keep the foundries running. This makes community colleges a crucial piece of the microelectronics workforce puzzle, Thompson says. In Ohio, the company is giving most of its educational funds to technical and community colleges so they can add semiconductor-specific training to existing advanced manufacturing programs. Intel is also asking universities to provide hands-on clean-room experience to community college students.

Samsung and Silicon Labs in Austin are similarly investing in neighboring community colleges and technical schools via scholarships, summer internships, and mentorship programs.
Beyond the deserts of Arizona, chipmakers are eyeing the America's midwest, the article points out (with its "abundance of research universities and technical colleges.")

• Indiana's Purdue launched a new interdisciplinary Semiconductor Degrees Program (building on its Defense Department-funded SCALE program which teaches how to build semiconductors for space), and they've partnered with a local community college to offer training for jobs at the West Lafayette foundry SkyWater.

• The University of Illinois Urbana-Champaign offers an Advanced Systems Design class "which leads senior-year undergrads through every step of making an integrated circuit."

• Intel has pledged $50 million to 80 higher-education institutions in Ohio to "upgrade their curricula, train and hire faculty, and provide equipment," including the funding of a Center for Advanced Semiconductor Fabrication Research and Education to teach semiconductor-related skills to more than just electrical engineering majors.

Last week the Telegraph reported that a recent firmware update to HP printers "prevents customers from using any cartridges other than those fitted with an HP chip, which are often more expensive. If the customer tries to use a non-HP ink cartridge, the printer will refuse to print."

Some HP "Officejet" printers can disable this "dynamic security" through a firmware update, PC World reported earlier this week. But HP still defends the feature, arguing it's "to protect HP's innovations and intellectual property, maintain the integrity of our printing systems, ensure the best customer printing experience, and protect customers from counterfeit and third-party ink cartridges that do not contain an original HP security chip and infringe HP's intellectual property."

Meanwhile, Engadget now reports that "a software update Hewlett-Packard released earlier this month for its OfficeJet printers is causing some of those devices to become unusable." After downloading the faulty software, the built-in touchscreen on an affected printer will display a blue screen with the error code 83C0000B. Unfortunately, there appears to be no way for someone to fix a printer broken in this way on their own, partly because factory resetting an HP OfficeJet requires interacting with the printer's touchscreen display. For the moment, HP customers report the only solution to the problem is to send a broken printer back to the company for service.
BleepingComputer says the firmware update "has been bricking HP Office Jet printers worldwide since it was released earlier this month..." "Our teams are working diligently to address the blue screen error affecting a limited number of HP OfficeJet Pro 9020e printers," HP told BleepingComputer... Since the issues surfaced, multiple threads have been started by people from the U.S., the U.K., Germany, the Netherlands, Australia, Poland, New Zealand, and France who had their printers bricked, some with more than a dozen pages of reports.

"HP has no solution at this time. Hidden service menu is not showing, and the printer is not booting anymore. Only a blue screen," one customer said.

"I talked to HP Customer Service and they told me they don't have a solution to fix this firmware issue, at the moment," another added.

"Driving an electric vehicle in Texas is soon to become more expensive," reports Gizmodo: Governor Greg Abbott signed a law (SB 505) on May 13 instituting new fees for registering and owning EVs in the state. Under the bill, electric car owners will have to pay $400 upon registering their vehicle. Then, every subsequent year, EV drivers will have to shell out an additional $200. Both of those fees are on top of the cost of the standard annual registration renewal fees, which are $50.75 each year for most passenger cars and trucks.

At least 32 states currently have special electric vehicle registration fees, according to data from the National Conference of State Legislatures. These range from $50 in places like Colorado, Hawaii, and South Dakota to $274 (starting in 2028) in a recently passed piece of Tennessee legislation...

Like many other states that have instituted EV fees, the reasoning behind the Lone Star State's new law is that electric car drivers don't buy gas. Taxes at the fuel pump are the primary way that most states, Texas included, amass funds for road construction, maintenance, and other driving-related infrastructure.
The bill's author told a local news station that "with the growing use of EVs, the revenue from the fuel tax is decreasing, which diminishes our ability to fund road improvements for all drivers."

But Gizmodo notes that Texas's gas tax "is among the lowest in the country, at just $0.20 per gallon." (And the average car uses less than 500 gallons a year, according to the American Petroleum Institute.)

Apple is reportedly expanding its involvement in the mass production of micro-LED displays to reduce its reliance on Samsung and gain more control over the supply chain. Nikkei Asia reports: Apple has spent heavily on the development of micro-LED displays over the past decade and once production starts, it intends to perform the critical "mass transfer" step of the manufacturing process itself, according to sources involved in the project. The mass transfer step involves moving at least tens of thousands of tiny micro-LED chips onto substrates. This process will be carried out at Apple's secretive R&D facilities in the Longtan District in the northern Taiwanese city of Taoyuan, according to multiple people with direct knowledge of the project.

Displays are one of the most expensive components in all of Apple's devices. Since the American company first introduced OLED displays on its iPhone in 2017, its reliance on Samsung Display for the screens has only grown. To reduce that dependence and gain price-bargaining power, Apple tried to bring in other suppliers, namely LG Display and China's display champion BOE Technology, but they lag the South Korean leader in terms of technology and quality stability, according to multiple sources familiar with the situation.

"Apple has spent at least $1 billion on the R&D and samples for micro-LED technologies in the past nearly 10 years," said one of the people who has been directly involved in the project for years. "It wants to secure more control over the next-gen display technologies for its future products." For the project, Apple is partnering with suppliers like ams-Osram for micro-LED components, LG Display for the substrates -- also called backplates -- and Taiwan Semiconductor Manufacturing Co. for 12-inch wafers. In addition to designing the driver integrated circuits for the micro-LED screens, Apple even designed some of the production equipment itself to better control the mass transfer process, according to two of the people with direct knowledge of the matter. "It doesn't mean that Apple will always do the mass transfer on its own. But it shows how determined Apple is to allocate resources to have more control over [these] next-gen display technologies in its own hands," one of the sources said.

"Apple's ultimate plan is to introduce the technologies on its iPhone, which is its key revenue source and has much bigger volume, to justify the investments over the years," added one of the sources.

An anonymous reader quotes a report from Tom's Hardware: YouTuber Jeff Geerling recently flew over to the UK to sit down with Raspberry Pi CEO Eben Upton for a chat about shortages, predictions, the Raspberry Pi Pico and other hot topics. The short of it is that stock levels are improving, close to Upton's 2022 prediction and that we are now seeing better stock levels than 2022 as Raspberry Pi slowly catches up with the backlog. Upton explained the reasoning behind prioritizing OEM customers over consumers, and addresses some of the negativity that was levied on Raspberry Pi by a minority of the passionate and vocal community.

The video starts with Geerling candidly explaining that his trip to the UK was not funded by Raspberry Pi, rather it was funded via sponsorship and Patreon supporters. With that out of the way Geerling covers a series of topics with Upton, and we've been through the video and pulled out the key points, with timestamps for you to listen to. In regard to the company's product and shipment progress, Upton said: "So quarter one this year was our worst quarter in terms of production and shipment. [...] We did about 750 to 800,000 units in Q1 this year [due to shifting production during the Christmas period]."

With progress being made on filling backlog and availability, Upton said the company expects to move two million units in the second quarter, with the third and fourth quarters of 2023 being "unconstrained."

Spacetop, a $2,000 laptop developed by two former Magic Leap employees, replaces the traditional screen with augmented reality glasses featuring a 100-inch virtual display. Axios reports: The company is selling 1,000 of the devices as part of an early access program, with hopes of using the feedback to inform a broader launch. The Spacetop runs a custom operating system, with its backers touting the ability to run Web-based applications such as Zoom, Google Workspace and Figma. And it's not promising this first version will be for power users or gamers, saying those folks should probably wait for a later version.

The Tel Aviv-based company behind the startup, Sightful, is led by CEO Tamir Berliner and COO Tomer Kahan, both formerly of AR headset maker Magic Leap. They have raised $61 million in venture funding. The devices are being manufactured by Wistron, a major contract manufacturer of laptops, while the required AR glasses come from Nreal. Those interested can sign up now, with the devices promised for shipping starting in July.

Sightful says the glasses offer 1080p resolution per eye, which they promise is enough to offer sub-pixel viewing resolution. In a pinch the Spacetop can also connect to a traditional monitor for some features, with more available later via software updates. Further reading:
I used the world's first augmented reality laptop (The Verge)
Meet Spacetop, a radical new laptop with no screen (PCWorld)
New Spacetop Laptop Puts Your Workspace in the Air (The New Stack)

Dublin-based company Gazelle Wind Power has developed a modular floating offshore wind turbine design that it claims is more affordable than traditional designs. The Register reports: While it still has to be anchored to the seafloor, Gazelle's design places the anchor cables on a trio of articulated arms that help the platform move with the motion of the ocean. To ensure the turbine tower itself stays stationary, a counterweight hangs from the center of the platform; Gazelle claims this will reduce the turbine's pitch to less than five degrees, which the company said will greatly reduce wear and tear on the tower. Despite those design changes, the result is a turbine base that Gazelle reckons is smaller, lighter and 30 percent cheaper to deploy compared to traditional semi-submersible designs, it said. Speaking to IEEE Spectrum recently, Gazelle CTO Jason Wormald claimed the counterbalanced turbine was designed from the ground up, so to speak, for the offshore wind industry.

Gazelle's design has yet to be fielded - it's working on a pilot project in Portugal with renewable energy firm WAM Horizon, whose Chairman also serves as a non-executive director at Gazelle -- but if test results scale well it could mean every 1GW of third-generation Gazelle towers deployed would use 71kt less steel, preventing around 100kt of carbon dioxide emissions, the company claims. Gazelle also touts its modular design, which it said doesn't require any specialized equipment, like cranes or custom-built launch vessels, as another way in which it reduces environmental impacts.

Hanging on to your favorite wireless mouse just got a little easier thanks to a new partnership between Logitech and DIY repair specialists iFixit. The Verge: The two companies are working together to reduce unnecessary e-waste and help customers repair their own out-of-warranty Logitech hardware by supplying spare parts, batteries, and repair guides for "select products." Everything will eventually be housed in the iFixit Logitech Repair Hub, with parts available to purchase as needed or within "Fix Kits" that provide everything needed to complete the repair, such as tools and precision bit sets. Starting "this summer," Logitech's MX Master and MX Anywhere mouse models will be the first products to receive spare parts. Pricing information has not been disclosed yet, and Logitech hasn't mentioned any other devices that will receive the iFixit genuine replacement parts and repair guide treatment.

India is unveiling a 170 billion-rupee ($2.1 billion) financial incentive plan to draw makers of laptops, tablets and other hardware to the South Asian nation as companies look to diversify supply chains beyond China. From a report: Prime Minister Narendra Modi is capitalizing on the early success of Apple's local assembly operations -- which have helped the US company produce about 7% of its global iPhone output -- to pitch the country as a viable global manufacturing hub. New Delhi wants to bring more tech production to India after China's trade war with the US and its strict Covid policies prompted companies to weigh other options. Apple has yet to begin making iPads or MacBook laptops in India, but fresh incentives could push the Cupertino, California-based company to consider such moves. Other manufacturers who could take advantage of the new measures include Dell, HP and Asustek Computer.

According to Agence France-Presse, France has opened an investigation into planned obsolescence of Apple products. From the report: The probe into purported misleading commercial practices and planned obsolescence has been under way since December, the Paris prosecutor's office said. It follows a complaint filed by the Halt Planned Obsolescence (HOP) association.

HOP said it hoped the investigation would demonstrate the iPhone maker was "associating the serial numbers of spare parts to those of a smartphone, including via microchips, giving the manufacturer the possibility of restricting repairs by non-approved repairers or to remotely degrade a smartphone repaired with generic parts." The association called on Apple "to guarantee the right to repair devices under the logic of real circular economy."

An anonymous reader quotes a report from Ars Technica: StorCentric, the holding company for the Drobo and Retrospect brands, filed for Chapter 11 bankruptcy in late June 2022. Now, AppleInsider reports that, based on an email sent by StorCentric, the bankruptcy shifted from reorganization-minded Chapter 11 to liquidation-focused Chapter 7 in late April.

The writing for Drobo was on the wall, or at least on its website. Text at the top of the homepage notes that, as of January 27, 2023, Drobo products and support for them are no longer available. "Drobo support has transitioned to a self-service model," the site reads. "We thank you for being a Drobo customer and entrusting us with your data." Drobo began in 2005 as Data Robotics and launched into the tech consciousness with the original Drobo, a "storage robot." The marquee feature was being able to hot-swap drives of nearly any size without migrating data.